ELECTRO NATIONAL CORPORATION
Canton, Mississippi (MS), United States
Aerospace
Products & Services
Standards Products
Electro National Corporation
We strive to continuously expand our standard product line to meet the current and future needs of our customers.
• Pressure Switches
• Rotary Stepping Switches
• Armature Relays
• Reed Relays
• Reed Switch
• Minireeds
• Drireeds
• Current Sensors
• Actuators
• Coil Assemblies
• Solenoids
• PC Boards
• Power Distribution Panels
• Wiring Harnesses
• Cable Assemblies
• Electromechanical Assembly
• Hard Line Tube Bending
• Pressure Switches
• Rotary Stepping Switches
• Armature Relays
• Reed Relays
• Reed Switch
• Minireeds
• Drireeds
• Current Sensors
• Actuators
• Coil Assemblies
• Solenoids
• PC Boards
• Power Distribution Panels
• Wiring Harnesses
• Cable Assemblies
• Electromechanical Assembly
• Hard Line Tube Bending
Custom Manufacturing
Electro National Corporation
The ENC custom manufacturing team members come from a variety of backgrounds and possess an abundance of experience, both from a design and a manufacturing stand point.
• Electromechanical Assembly
• Test Set Design
• Ground Support Equipment
• Aviation Grade Design & Assembly
• Wiring Harnesses
• Cable Assemblies
• Fabrication
• Coil Winding
• Design Engineering
• Reverse Engineering
• Integration of Systems
Because of our design and manufacturing capabilities, ENC is the optimal choice for any custom manufacturing needs.
ENC strives to ensure that requirements for custom manufactured products are precisely understood and communicated to our production team. Some of the many processes we employ to make certain that products conform to requirements are shown in the diagram below. We not only aim to build exceptional products, but to build satisfied, loyal, repetitive customers.
• Electromechanical Assembly
• Test Set Design
• Ground Support Equipment
• Aviation Grade Design & Assembly
• Wiring Harnesses
• Cable Assemblies
• Fabrication
• Coil Winding
• Design Engineering
• Reverse Engineering
• Integration of Systems
Because of our design and manufacturing capabilities, ENC is the optimal choice for any custom manufacturing needs.
ENC strives to ensure that requirements for custom manufactured products are precisely understood and communicated to our production team. Some of the many processes we employ to make certain that products conform to requirements are shown in the diagram below. We not only aim to build exceptional products, but to build satisfied, loyal, repetitive customers.
About
ENC was established in 1974 when we purchased the pressure switch, reed relay, current sensor, and reed switch product lines from Hathaway Instruments in Tulsa, Oklahoma and moved these lines to Canton, Mississippi.
In 1980, ENC added the stepping switch and relay lines purchased from GTE Automatic Electric. In 1984, we purchased three additional lines: rotary switch, "E" relay, and correed relay, to compliment our existing products.
We are still manufacturing all of these products. We are continuously searching for new products to add to our existing standard line, which began the custom manufacturing portion of our operation.
ENC is centrally located in the Southeast United States in Canton, Mississippi. Canton is located less than 22 miles from Jackson, Mississippi, the State's Capital, with direct access to a multi-directional interstate system.
Structure Type: Brick and Concrete
Total Square Footage: 40,000
Manufacturing Square Footage: 24,400
Office Square Footage: 5,600
Warehouse/Expansion
Square Footage: 1,200
Land/Expansion: 4 acres
ENC is certified by the SBA as a Small Disadvantaged Business (Minority-Owned).
Canton is located within 3 hours of the largest water access ports available in the United States, as well as 3 major international airports - all of which allow us the most efficient forms of transportation of parts to and from our customers.
In 1980, ENC added the stepping switch and relay lines purchased from GTE Automatic Electric. In 1984, we purchased three additional lines: rotary switch, "E" relay, and correed relay, to compliment our existing products.
We are still manufacturing all of these products. We are continuously searching for new products to add to our existing standard line, which began the custom manufacturing portion of our operation.
ENC is centrally located in the Southeast United States in Canton, Mississippi. Canton is located less than 22 miles from Jackson, Mississippi, the State's Capital, with direct access to a multi-directional interstate system.
Structure Type: Brick and Concrete
Total Square Footage: 40,000
Manufacturing Square Footage: 24,400
Office Square Footage: 5,600
Warehouse/Expansion
Square Footage: 1,200
Land/Expansion: 4 acres
ENC is certified by the SBA as a Small Disadvantaged Business (Minority-Owned).
Canton is located within 3 hours of the largest water access ports available in the United States, as well as 3 major international airports - all of which allow us the most efficient forms of transportation of parts to and from our customers.
